Jr.Integration Engineer
Preamble: Unistring Tech Solutions presents a unique opportunity through its Knowledge and Skills Enhancement Initiative. By offering essential video content for training materials, it enables individuals to grab internship opportunities.
Disclaimer: The role and responsibilities mentioned in the below Job Description are and indicative. Based on the performance, there may be a change as per the requirements.
Note: Responsibilities and Assessment Questions can be found after video content.
Skill and Knowledge Elements
Responsibilities
1.Responsible for completing the LRU integration as per defined process and execution with the help of technical assts.
2.Identification All components of LRU.
3.Interconnecting the modules in the LRU based on check sheets.
4.Operations of Test setups/ Test jigs as per the defined process during the LRU integration.
5.Performing the hardware to software handover procedure as per the defined process.
6.LRU placements and i/p o/p of each module and i/p o/p of plate level as per defined process.
7.Filling integration check sheets as per the defined process.
8.
Any unexpected or unfrozen delays need to inform the LRU Lead.
Sample Assessment Questions
1. For a circuit requiring a maximum current of 20 amps, which AWG wire should be used?
- A. 18AWG
- B. 16AWG
- C. 14AWG
- D. 12AWG
2. What is the diameter of a 10 AWG wire?
- A. 2,59mm
- B. 1.30mm
- C. 5.26mm
- D. 0.81mm
3. A device operates at 120 volts and 15 amps. What is its power consumption?
- A. 1800 watts
- B. 135 watts
- C. 105 watts
- D. 8 watts
4. What is the resistance of a circuit that uses 10 watts of power with a current of 2 amps?
- A. 5 ohms
- B. 0.5 ohms
- C. 20 ohms
- D. 2.5 ohms
5. If you are measuring the resistance of a resistor that you expect to be around 330 ohms, what setting should you use on the multimeter?
- A. 200 ohms
- B. 2k ohms
- C. 200k ohms
- D. 20M ohms
6. When measuring a circuit that is expected to draw 500mA, the multimeter should be set to:
- A. The 200mA range
- B. The 20A range
- C. The 10A range
- D. The 2A range
7. If a torque wrench has a minimum increment of 5 Nm on its scale, what is the smallest torque setting you can accurately apply?
- A. 1 Nm
- B. 5 Nm
- C. 10 Nm
- D. 0.5 Nm
8.Which of the following best describes the pin configuration of a standard DB-9 male connector, commonly used for RS-232 serial communications?
- A. 5 rows and 10 columns of pins
- B. 2 rows of pins, with 5 pins in the first row and 4 in the second row
- C. 1 row of 9 pins
- D. 3 rows of 3 pins each
9. Which of the following best describes how to identify the gender of an SMA connector?
- A. The male connector has a pin, and the female connector has a socket.
- B. The male connector has a socket, and the female connector has a pin.
- C. The male connector is larger in diameter than the female connector.
- D. The female connector is identified by the outer threading, while the male connector has inner threading.
10.Which of the following options best describes the purpose and implementation of thread locking mechanisms in SMA connectors?
- A. To increase the electrical conductivity between connected devices by providing a tighter connection.
- B. To prevent the connector from loosening due to vibration or rotational forces, ensuring a stable and secure connection.
- C. To waterproof the connection, protecting it against moisture and liquid damage.
- D. To enhance the data transmission speed by securing the connector in an optimal alignment.